I have laid some Bradstone Old Town Flags on 10/1 bed.
3 days later when I went back to grout some of the flags were rocking slightly.
When I laid the flags Should i have loosened the the top layer with trowel after screeding.
Will Grouting with 4/1 dry mix pervent rocking
Best regards.
Bradstone flags
-
84-1093879891
Did you simply prepare a screeded bed (not recommended for this type of flag) and then plonk down the flags without consolidating them?
I recommend the individual bedding method for these flags, as a screeded bed cannot accommodate the variations in thickness, but even with a screeded bed, the flags need to be consolidated by tapping "to refusal" with a pavior's maul, as described on the main website.
Pointing flags that are already rocking will hold them firm in the short term, but, after a week or two, they'll start to move again. It's essential that the flags are firm and stable before pointing.
I recommend the individual bedding method for these flags, as a screeded bed cannot accommodate the variations in thickness, but even with a screeded bed, the flags need to be consolidated by tapping "to refusal" with a pavior's maul, as described on the main website.
Pointing flags that are already rocking will hold them firm in the short term, but, after a week or two, they'll start to move again. It's essential that the flags are firm and stable before pointing.
-
CRAZYPAVER
- Posts: 5
- Joined: Tue Jun 15, 2004 10:48 am
- Location: Wexford Ireland
-
84-1093879891
-
CRAZYPAVER
- Posts: 5
- Joined: Tue Jun 15, 2004 10:48 am
- Location: Wexford Ireland
-
84-1093879891
You might be able to 'tighten up' the 10 loose flags by making a very, very wet mortar slurry, 3:1 mix of BUILDING sand with cement, a dash of plasticiser, and mixed to the consistency of Tomato soup. Mix it in a bucket and keep stirring to prevent it settling.
Very, very carefully pour it into the joints around the loose flags, and then straddle the flags and cause them to rock, so that they draw in the slurry to fill any minor voids. If you spill or splash any of the slurry on the surface of the flags, wash off immediately with clean water.
The slurry should set in 24 hours or so and hold the flags tight. The idea of using building sand, rather than the usual grit sand, is that it consists of finer grains and so offers enhanced workability as a slurry and can rget to the parts other sands can't reach.
Once they've been treated with the slurry, don't let anyone walk on them for at least 24 hours, preferably 48-72 hours, if poss.
As to where you went wrong, the most frequent cause is incomplete consolidation. It's not always easy to spot that a flag is moving ever so slightly when laid, so it's worth checking each flag two or three times. The second biggest culprit is allowing the edges of the flags to be trafficked too soon. If you have to walk across the newly paved surface, try to ensure your foot falls only on the centre of the larger flags, and not on the edges or on the smaller (300x300mm) units.
As luck would have it, if the joints are buttered when laid, this can help keep the flags firm while the bedding hardens off, but, if you think this could be a problem likely to recur, consider using a moist mix, rather than semi-dry, for the bedding. This uses a minimal amount of added water, just enough to bind everything together, and can sometimes be a bit more forgiving of partial consolidation than a semi-dry mix.
Very, very carefully pour it into the joints around the loose flags, and then straddle the flags and cause them to rock, so that they draw in the slurry to fill any minor voids. If you spill or splash any of the slurry on the surface of the flags, wash off immediately with clean water.
The slurry should set in 24 hours or so and hold the flags tight. The idea of using building sand, rather than the usual grit sand, is that it consists of finer grains and so offers enhanced workability as a slurry and can rget to the parts other sands can't reach.
Once they've been treated with the slurry, don't let anyone walk on them for at least 24 hours, preferably 48-72 hours, if poss.
As to where you went wrong, the most frequent cause is incomplete consolidation. It's not always easy to spot that a flag is moving ever so slightly when laid, so it's worth checking each flag two or three times. The second biggest culprit is allowing the edges of the flags to be trafficked too soon. If you have to walk across the newly paved surface, try to ensure your foot falls only on the centre of the larger flags, and not on the edges or on the smaller (300x300mm) units.
As luck would have it, if the joints are buttered when laid, this can help keep the flags firm while the bedding hardens off, but, if you think this could be a problem likely to recur, consider using a moist mix, rather than semi-dry, for the bedding. This uses a minimal amount of added water, just enough to bind everything together, and can sometimes be a bit more forgiving of partial consolidation than a semi-dry mix.