The Brew Cabin

Posted: **Sun Jul 05, 2015 10:56 am**

im going to be getting a wooden log cabin style workshop soon as ive got the time to get on with it

but im unsure if id be able to do the base myself and also what spec it would need to be :p any help gratefully received its going to be approx. 3.5 x 7 m

Posted: **Sun Jul 05, 2015 11:41 am**

Michael there is a complete guide on the index page under concrete bases ???

Posted: **Sun Jul 05, 2015 12:27 pm**

yes ive seen that so I suppose my only real question is how thick should it be and do I need reinforcement :rock:

Posted: **Sun Jul 05, 2015 12:47 pm**

100 ml will be fine with a single layer of mesh.

Posted: **Sun Jul 05, 2015 7:07 pm**

Depends whats going in the workshop if yoru putting a car in i would go 150mm with the concrete

Posted: **Tue Jul 07, 2015 10:42 am**

The last drawing in this section shows a standard shed base construction.

Posted: **Fri Oct 09, 2015 7:51 am**

well this has ground to a halt im sorry to say work got in the way so ive only jut got the old shed cleared now ive got to get it taken away ( asbestos ) but I was thinking do you think block paving would do the job to be honest the thought of concrete scares me a bit not something ive done on that scale and not exactly forgiving is it if I fook up ! also ive seen some blocks on ebay

Posted: **Fri Oct 09, 2015 9:27 am**

If its has ita own floor you could always run 3 rows of brick or blocks as a footing to build off of

Posted: **Sat Oct 10, 2015 7:47 am**

not going to have a floor that's extra

Posted: **Sat Oct 10, 2015 7:48 am**

michaelthegardener wrote:well this has ground to a halt im sorry to say work got in the way so ive only jut got the old shed cleared now ive got to get it taken away ( asbestos ) but I was thinking do you think block paving would do the job to be honest the thought of concrete scares me a bit not something ive done on that scale and not exactly forgiving is it if I fook up ! also ive seen some blocks on ebay

if it is existing block paving then you are half way there if the existing sub base is sound. i'd do away with the blocks and put in a slab Michael. I wouldn't think concreting to be above your capabilities

Posted: **Sat Oct 10, 2015 10:31 am**

Concrete slab would be best ideally you want the timber above the surrounding ground are you raising the slab up or running course of brick/block for it to sit on? If its just a flat concrete slab make sure you have the cladding or a flashing/drip tray over the side if the concrete base to send the water away from the workshop

Posted: **Sat Oct 10, 2015 6:53 pm**

all that is there is the old cracked 1974 concrete I know concrete would be best but was thinking ive done a bit of block paving before but not concrete on this scale

Posted: **Sat Oct 10, 2015 8:36 pm**

Concrete os fairly straight forward build your shutter, fill it, tamp it drag the excess off then finish how ever you want
Depends on the type of finish your after id it was me id do a float finish so its smooth to stand on and easy to brush clean.
I suppose it would all come down to cost and wether you can get someone to help you as for the concrete pad if its 150mm deep your looking around 4m3 of concrete (get it delivered instead of mixing it by hand) so a fair bit of barrowing

Posted: **Sun Oct 11, 2015 10:50 am**

Michael RX is right
blockpaving will cost you money long term

we did a 4m3 oversite friday 3 barrowing and me levelling it took us 90minutes

however the concrete cost Â£600 +vat

but a 150 mm deep slab will last the course
LLL

Posted: **Tue Oct 13, 2015 8:02 am**

ok so if it all goes wrong ill blame you lot !:D im a bugger for ebay and that's where I saw some cheap blocks

the workshops costing me 3350 quid so I know youre all right about needing the best base not spending all that for it to sink :0

One last question though on the main site it says Maximum size approx 6m x 3m. Should NOT exceed 20mÂ² so what do I do about that ?

The Brew Cabin

Workshop base