Rushed pointing - Smeared cement stains

Patio flagstones (slabs), concrete flags, stone flags including yorkstone and imported flagstones.
Post Reply
smobb
Posts: 13
Joined: Tue Feb 24, 2015 8:07 pm
Location: Derby

Post: # 107054Post smobb

Hi,

Been having a bit of a nightmare recently with the weather, finally got a dry day and went in hard doing as much pointing of some sandstone paving as i could. Unfortunately now it's dried i can see in my haste i managed to smear some cement from the joints on the edges of the flags. I'm pretty sure i did this by brushing off any excess mortar a little too soon while it was still a bit wet.

i'm finding this pretty distressing as i'm a bit of a stickler for this type of thing and where i'm usually pretty clean but i made a bad judgment call during my elation over it stopped raining, got a bit sloppy.

What's the best way of removing a smeared cement stain do you reckon? a wire brush seems like it would damage the slab as it's not like its a clump of dried mortar and i'm not going near any brick acid due to it being sandstone. just seems like it's one with the slab. any ideas??

RAPressureWashing
Posts: 985
Joined: Wed Aug 15, 2007 3:02 pm
Location: Staines Surrey
Contact:

Post: # 107055Post RAPressureWashing

Phosphoric acid substitute
Bought from here
http://www.tilinglogistics.co.uk/Tile-pr....c-spray
Roger Oakley BDA(Europe)Member 2006
R&A Pressure Washing Services Ltd
info@rapressurewashing.co.uk
www.rapressurewashing.co.uk

smobb
Posts: 13
Joined: Tue Feb 24, 2015 8:07 pm
Location: Derby

Post: # 107056Post smobb

Cheers for reply.Being acid based will this not be risky with sandstone?? especially indian sandstone.

lutonlagerlout
Site Admin
Posts: 15184
Joined: Fri Aug 04, 2006 12:20 am
Location: bedfordshire

Post: # 107057Post lutonlagerlout

brick acid is fine with most indian sandstones
its lime stone you have to watch out for
of course you need to check it on an offcut first

always pre wet stone before you use acid
LLL
"what,you want paying today??"

YOUR TEXT GOES HERE

smobb
Posts: 13
Joined: Tue Feb 24, 2015 8:07 pm
Location: Derby

Post: # 107058Post smobb

ok cheers.

i've seen some discolouring of indian sandstone from previous experience using brick acid, nothing major but similar to whats described in the staining page on this site. Also after reading more about the product described above it doesn't mention sandstone as an approved material to use it on...... so i remain slightly uneasy haha. i'll just make sure to test it on a few off cuts first!

thanks for the advice.

RAPressureWashing
Posts: 985
Joined: Wed Aug 15, 2007 3:02 pm
Location: Staines Surrey
Contact:

Post: # 107059Post RAPressureWashing

smobb wrote:Cheers for reply.Being acid based will this not be risky with sandstone?? especially indian sandstone.
It will be fine, if not I wouldn't have recommended it.
Follow the instructions to the letter that is on the packaging and I'd use a stiff nylon brush as these are fairly chemical proof.

Acids to be avoided is Hydrochloric acid aka brick acid one reason is it comes in different strengths and to many people don't read the labelling so this is when accidents happen.
But do a test area or piece if you can, pre-wet the stone mix the phosphoric down to suggested mix as per the instructions and dwell time. Depending on the staining you might need to have a couple of attempts.
Roger Oakley BDA(Europe)Member 2006
R&A Pressure Washing Services Ltd
info@rapressurewashing.co.uk
www.rapressurewashing.co.uk

RAPressureWashing
Posts: 985
Joined: Wed Aug 15, 2007 3:02 pm
Location: Staines Surrey
Contact:

Post: # 107060Post RAPressureWashing

smobb wrote:ok cheers.

i've seen some discolouring of indian sandstone from previous experience using brick acid, nothing major but similar to whats described in the staining page on this site. Also after reading more about the product described above it doesn't mention sandstone as an approved material to use it on...... so i remain slightly uneasy haha. i'll just make sure to test it on a few off cuts first!

thanks for the advice.
It's fine on Sandstone if you follow in the instructions, I use this on Limestone as well when needed.
Roger Oakley BDA(Europe)Member 2006
R&A Pressure Washing Services Ltd
info@rapressurewashing.co.uk
www.rapressurewashing.co.uk

smobb
Posts: 13
Joined: Tue Feb 24, 2015 8:07 pm
Location: Derby

Post: # 107065Post smobb

ok cheers mate, thanks for the info, i'll give it a go.

Post Reply