Manhole ring lifting pins

For the discussion of hand tools, power tools, operated and non-operated plant, and all sorts of kit associated with the paving and drainage trades
Post Reply
irishpaving
Posts: 420
Joined: Mon Jun 29, 2009 11:14 pm
Location: uk

Post: # 46856Post irishpaving

broken
"I'm spending a year dead for tax reasons."
Top
Tommy
Posts: 357
Joined: Sun Oct 08, 2006 9:46 pm
Location: Stoke

Post: # 46857Post Tommy

Photo is broken...
Top
seanandruby
Site Admin
Posts: 4713
Joined: Mon Jun 26, 2006 11:01 am
Location: eastbourne

Post: # 46879Post seanandruby

can,t see photo, so am assuming they are your own. How long have yoi had them and how did they break? Did you inform the hse? Time and time again i see guys in the hole with a ring swinging above them and pins in the wrong way round. I've seen them shake lose being wrong way whilst tracking along on 360. They break so easy, so do bones.
sean
Top
GB_Groundworks
Site Admin
Posts: 4420
Joined: Sat Aug 09, 2008 3:55 pm
Location: high peak
Contact:
Contact GB_Groundworks

Post: # 46881Post GB_Groundworks

did you post a photo or just post broken haha

we have a few sets ones you push through and then slide a washer and split pin or ones that slide through then the end cranks over and slides down to make a T shape.

sean by pins in the wrong way round what you mean, the rings outside the manhole ring?

we have these

Image



Edited By GB_Groundworks on 1268082684
Giles

Groundworks and Equestrian specialists, prestige new builds and sports pitches. High Peak, Cheshire, South Yorkshire area.

http://www.gbgroundworks.com
Top
msh paving
Site Admin
Posts: 1854
Joined: Tue Aug 19, 2008 7:03 pm
Location: kings lynn norfolk
Contact:
Contact msh paving

Post: # 46885Post msh paving

this lifter is what i use all the time they are german got them from ebay £80 just push them on a ring equi-distant around the ring
Image

MSH :)
paving, mini-crusher, mini-digger hire and groundwork
http://mshpaving.co.uk
Top
msh paving
Site Admin
Posts: 1854
Joined: Tue Aug 19, 2008 7:03 pm
Location: kings lynn norfolk
Contact:
Contact msh paving

Post: # 46886Post msh paving

the heaver the ring the stronger the grip , no pins to lose chains are fixed to them tested to 2.5 ton on the chain, MSH :)
paving, mini-crusher, mini-digger hire and groundwork
http://mshpaving.co.uk
Top
Dave_L
Site Admin
Posts: 4732
Joined: Fri Jul 28, 2006 8:47 pm
Location: Somerset
Contact:
Contact Dave_L

Post: # 46888Post Dave_L

Nice, I like them.

We have got the ones with the eyes and a threaded section and nuts. Fiddly, but don't often lift Milton rings in these days.
RW Gale Ltd - Civils & Surfacing Contractors based in Somerset

See what we get up to Our Facebook page
Top
flowjoe
Posts: 1136
Joined: Sun May 08, 2005 9:25 am
Location: North West

Post: # 46898Post flowjoe

Internal dropshaft MSH ?
http://draindomain.com

Many paths can lead to riches, few in sunlight, some in ditches
Top
msh paving
Site Admin
Posts: 1854
Joined: Tue Aug 19, 2008 7:03 pm
Location: kings lynn norfolk
Contact:
Contact msh paving

Post: # 46899Post msh paving

you got it flojoe, was a crap job, 4 water services ontop off the clay 6" pipe ,angle all wrong client did not what to pay the proper price , as 4 waters had to be cut and jointed total 8 times no one knew they was there MSH :)
paving, mini-crusher, mini-digger hire and groundwork
http://mshpaving.co.uk
Top
msh paving
Site Admin
Posts: 1854
Joined: Tue Aug 19, 2008 7:03 pm
Location: kings lynn norfolk
Contact:
Contact msh paving

Post: # 46900Post msh paving

ground water was at invert leval, MSH
paving, mini-crusher, mini-digger hire and groundwork
http://mshpaving.co.uk
Top
seanandruby
Site Admin
Posts: 4713
Joined: Mon Jun 26, 2006 11:01 am
Location: eastbourne

Post: # 46903Post seanandruby

yes the rings should be outside. Yes i know before you say it, 'if you lift two rings that way they will tip and you'll smash one.' But you are'nt supposed to lift two.
sean
Top
lutonlagerlout
Site Admin
Posts: 15184
Joined: Fri Aug 04, 2006 12:20 am
Location: bedfordshire

Post: # 46909Post lutonlagerlout

i really am confused now
LLL
"what,you want paying today??"

YOUR TEXT GOES HERE
Top
irishpaving
Posts: 420
Joined: Mon Jun 29, 2009 11:14 pm
Location: uk

Post: # 46915Post irishpaving

The pins are the ones on the right hand side of Giles picture. There not broken there New. Just wanted to see if any1 was interested in purchasing them.
"I'm spending a year dead for tax reasons."
Top
msh paving
Site Admin
Posts: 1854
Joined: Tue Aug 19, 2008 7:03 pm
Location: kings lynn norfolk
Contact:
Contact msh paving

Post: # 46941Post msh paving

how much irish? MSH :)
paving, mini-crusher, mini-digger hire and groundwork
http://mshpaving.co.uk
Top
seanandruby
Site Admin
Posts: 4713
Joined: Mon Jun 26, 2006 11:01 am
Location: eastbourne

Post: # 46975Post seanandruby

msh paving wrote:how much irish? MSH :)
just pin money :laugh:
sean
Top
Post Reply

Return to “Tools and Plant”