My block paving
-
- Posts: 10
- Joined: Tue Apr 07, 2009 10:02 pm
- Location: Hereford
The drive was already down when we moved in and as a result i am a little unsure of what to do with it.
Every year i just usually power wash it and seem to be forever spraying weed killer in between the joints to kill the weeds off. The drive has no car on it and has very light foot traffic infrequently.
This year i want to do it properly!! Have i damaged the paving in any way? I have been reading the forum about replacing the sand in the joints?
I suppose i'd just like a way of:
1: Killing the weeds
2: Ensuring as much as possible keeping them away.
3: Will i need to brush some of the fine sand over the joints?
4: Power wash again?
5: Seal it?
From Monday Aldi have a weed blowtorch available, a good idea??
Thanks Neil
Every year i just usually power wash it and seem to be forever spraying weed killer in between the joints to kill the weeds off. The drive has no car on it and has very light foot traffic infrequently.
This year i want to do it properly!! Have i damaged the paving in any way? I have been reading the forum about replacing the sand in the joints?
I suppose i'd just like a way of:
1: Killing the weeds
2: Ensuring as much as possible keeping them away.
3: Will i need to brush some of the fine sand over the joints?
4: Power wash again?
5: Seal it?
From Monday Aldi have a weed blowtorch available, a good idea??
Thanks Neil
-
- Site Admin
- Posts: 15184
- Joined: Fri Aug 04, 2006 12:20 am
- Location: bedfordshire
if you jet wash it ,then you will need to re-sand it when its dry
unless its a very poor construction weeds dont grow through block paving,just the seeds tend to lodge where people have blasted the sand out with a jetwasher :;):
you can seal it but if its as old as you say (sealer is expensive) might be best to relay
regards LLL
unless its a very poor construction weeds dont grow through block paving,just the seeds tend to lodge where people have blasted the sand out with a jetwasher :;):
you can seal it but if its as old as you say (sealer is expensive) might be best to relay
regards LLL
-
- Posts: 985
- Joined: Wed Aug 15, 2007 3:02 pm
- Location: Staines Surrey
- Contact:
Neil,
How bad is the weed problem? can you post a photo.
Might be worth getting it cleaned & re-sanded by a pro, then your maintenace side of things will be easy.
How bad is the weed problem? can you post a photo.
Might be worth getting it cleaned & re-sanded by a pro, then your maintenace side of things will be easy.
Roger Oakley BDA(Europe)Member 2006
R&A Pressure Washing Services Ltd
info@rapressurewashing.co.uk
www.rapressurewashing.co.uk
R&A Pressure Washing Services Ltd
info@rapressurewashing.co.uk
www.rapressurewashing.co.uk
-
- Posts: 10
- Joined: Tue Apr 07, 2009 10:02 pm
- Location: Hereford
Weeds not too bad but enough to iratate me lots! I'll get a picture in a mo. I'd like to think i'd be capable of power washing and resanding the joints.
What's the best way of de weeding? What about the burning one i mentioned? http://aldi.co.uk/uk/html/offers/2827_9475.htm
I suppose its never been re-sanded, i've been here 5 years and never done it.
How old would you say the block paving would be until it needs replacing on average?
What's the best way of de weeding? What about the burning one i mentioned? http://aldi.co.uk/uk/html/offers/2827_9475.htm
I suppose its never been re-sanded, i've been here 5 years and never done it.
How old would you say the block paving would be until it needs replacing on average?
-
- Posts: 64
- Joined: Mon Mar 16, 2009 10:45 pm
- Location: Huddersfield, West Yorkshire
- Contact:
If the block have never been re-sanded, you may end up doing more damage with a normal pressure washer as the blocks will become unstable.
After pressure washing, always replace the sand.
We did one a while back where the customer had done it himself every year and never resanded it. All that was in the joints was mud and dirt. Even using the proper machinery we started to see the sub-base coming out. At that point we immediatley stopped and used a manual method to at least get some sand in the joints, to then go back to pressure washing but on less than half power to get rid of most of the mud in the joints. it was of course resanded afterwards.
As previousley stated, get a proffesional in to do it this once, as i can envisage a diy job ruining the drive.
As regards to how long a block paved driveway should last... Well properly constructed from the start and proffesionally maintained, it should last many many many years.
After pressure washing, always replace the sand.
We did one a while back where the customer had done it himself every year and never resanded it. All that was in the joints was mud and dirt. Even using the proper machinery we started to see the sub-base coming out. At that point we immediatley stopped and used a manual method to at least get some sand in the joints, to then go back to pressure washing but on less than half power to get rid of most of the mud in the joints. it was of course resanded afterwards.
As previousley stated, get a proffesional in to do it this once, as i can envisage a diy job ruining the drive.
As regards to how long a block paved driveway should last... Well properly constructed from the start and proffesionally maintained, it should last many many many years.
Regards,
Andy Willcock
Amogen Drive, Decking & Patio Cleaners
Premier Exterior Surface Cleaners & Restorers
FREE Quotes & FREE Demonstrations - Nationwide Coverage
Website
info@amogen.com
Est. 2004
Andy Willcock
Amogen Drive, Decking & Patio Cleaners
Premier Exterior Surface Cleaners & Restorers
FREE Quotes & FREE Demonstrations - Nationwide Coverage
Website
info@amogen.com
Est. 2004
-
- Posts: 985
- Joined: Wed Aug 15, 2007 3:02 pm
- Location: Staines Surrey
- Contact:
Nice weeds.
Doesn't look like there is much sand in those joins either.
This really does need to be done professionally as you also have a fair bit of lichen on the pavers and your average shop bought pw is not going to remove this.
Heat and the right chemicals is the way forward on this.
With regards to the weeds yes put a strong weedkiller down say 1-2 weeks before hand to kill off the weeds, then have the area washed and allowed to dry out then re-sand.
From your profile you are in the Hereford area which way out of our area, but I do have a database and could check to see if you have someone local to you that I could put forward to at least quote on the work. Let me know.
Doesn't look like there is much sand in those joins either.
This really does need to be done professionally as you also have a fair bit of lichen on the pavers and your average shop bought pw is not going to remove this.
Heat and the right chemicals is the way forward on this.
With regards to the weeds yes put a strong weedkiller down say 1-2 weeks before hand to kill off the weeds, then have the area washed and allowed to dry out then re-sand.
From your profile you are in the Hereford area which way out of our area, but I do have a database and could check to see if you have someone local to you that I could put forward to at least quote on the work. Let me know.
Roger Oakley BDA(Europe)Member 2006
R&A Pressure Washing Services Ltd
info@rapressurewashing.co.uk
www.rapressurewashing.co.uk
R&A Pressure Washing Services Ltd
info@rapressurewashing.co.uk
www.rapressurewashing.co.uk
-
- Posts: 10
- Joined: Tue Apr 07, 2009 10:02 pm
- Location: Hereford
-
- Site Admin
- Posts: 15184
- Joined: Fri Aug 04, 2006 12:20 am
- Location: bedfordshire
-
- Posts: 10
- Joined: Tue Apr 07, 2009 10:02 pm
- Location: Hereford