Page 105 of 315

Posted: Thu May 10, 2012 9:15 pm
by lutonlagerlout
soakaway dug and crates installed
Image
advantex non woven and geo grid installed
Image
flat top edgings and drains connected
Image

btw any good tips for bagged tarmac?
the bit by the footpath is fecked but the council dont want to know?

and lastly 393 mesh over the soakaway then concreted in
Image
would have took more pictures but we had 17 tonnes of type 1 to barrow in in the pishing rain this afternoon
got soaked to the skin
tickets all booked for wembley on the 20th
loooo-ton!!
LLL :)

Posted: Thu May 10, 2012 9:22 pm
by dig dug dan
tarmac. Greenpatch repair from ronacrete. best stuff out there. done a patch on the farm track a year ago, its still holding.

out of interest, why can't you terram over the crates and type one. will it sink?? or are you a "belt and braces" man!

Posted: Thu May 10, 2012 9:38 pm
by Pablo
Tony I use those channels a lot they're not 252 rated but are fine for domestic drives. Top tip for you though take a grinder to every second nib on the tops because they're impossible to get off once everythings installed and tight. They sit very well with the missing nibs I've used them on that last set of pictures I've posted I pay about £6.10 each.

Posted: Thu May 10, 2012 9:46 pm
by lutonlagerlout
it was too wet for later pics
crates were surrounded by terram and shingle pipe was then laid on top and covered in more terram and shingle
then the mesh and concrete
then the terram and geogrid
I am not really happy about putting crates under someones drive and so would rather approach it belt and braces for a few quid extra
got gas ,electric and sewers to the lawn so could go that way
I hear ye paul about those channels,i had to remove some covers after a blockage and it nearly broke my heart,however i do like the wavy lines
found those flat tops in pinewood dan,they are smooth on 3 sides which i kinda liked
cheers LLL :)




Edited By lutonlagerlout on 1336682944

Posted: Thu May 10, 2012 9:59 pm
by lutonlagerlout
btw i may just go to the local tarmac plant and swallow it
what should i ask for I am guessing about .4 of a tonne but what mix?
cheers LLL

Posted: Thu May 10, 2012 10:13 pm
by msh paving
lutonlagerlout wrote:btw i may just go to the local tarmac plant and swallow it
what should i ask for I am guessing about .4 of a tonne but what mix?
cheers LLL
unless you have a account at the plant if its owned by tarmac they wont talk to you, usually 1ton min mix,if you dont have a insulated truck chances are you wont get a load, i would stick to the bagged stuff or cross a reinstatments gang with silver MSH :)

Posted: Thu May 10, 2012 11:31 pm
by Dave_L
.8t min mix, without a way of keeping its heat (insulated body etc) you'll be fighting a loosing battle.

Posted: Thu May 10, 2012 11:34 pm
by Dave_L
Pablo wrote:I pay about £6.10 each.
I hate the plastic channels, probably because most of my work is surfaced with bitmac and the heat destroys anything plastic.

You're paying nigh-on what I buy the resin 100mm Aco raindrains at for plastic items....it pays to shop around.

Posted: Thu May 10, 2012 11:36 pm
by Dave_L
Always very satisfying to have a line pulled through a drainage run after putting it all into a measure off a drainage drawing and it comes in like this...........

Image

Posted: Thu May 10, 2012 11:39 pm
by Dave_L
And on the upside, we've got the best drying room any site could ever wish for....the boilerhouse! Toasty warm! Found one of the site labourers asleep tucked in beside one of the boilers yesterday afternoon! Got to say, he was well hidden....

It's a great place to dry the drawings out during breaktimes :)

Image

Posted: Thu May 10, 2012 11:49 pm
by lutonlagerlout
Dave_L wrote:
Pablo wrote:I pay about £6.10 each.

I hate the plastic channels, probably because most of my work is surfaced with bitmac and the heat destroys anything plastic.

You're paying nigh-on what I buy the resin 100mm Aco raindrains at for plastic items....it pays to shop around.
resin acos for £6 quids???
pull the other one dave
i can get cheapo resin ones for tenners but the metal is poor
my supplier reckons aco are up their own arse and dont want to deal with anyone doing less than 100k a year
i didnt used to believe it but i reckon the hdpe ones are superior apart from where hot work is involved :;):
LLL

Posted: Thu May 10, 2012 11:59 pm
by mickg
I used instarmac tarmac in a tub about 5 weeks ago to make good a pavement similar to yours, worked a treat

Posted: Sat May 12, 2012 1:49 pm
by lutonlagerlout
100 tegula kerbs in
Image
crikey my wrist hurts :)
stone wacked to refusal
Image
curve set out and haunched
Image

its a funny drive this one
600 fall from garage to road and a 400 cross fall
i wanted to build a retaining wall but the client likes it as it is
cheers LLL

Posted: Sat May 12, 2012 1:53 pm
by lutonlagerlout
oh and cheers mickg for the tip with the penant grey kerbs
they do look a lot better than traditional against hazelnut
thanks
LLL
:)

Posted: Sat May 12, 2012 2:10 pm
by haggistini
Ooh that looks tidy LLL 45 degree or 90?