Cleaning marshalls monoblock....

All forms of block paving, brick paving, flexible or rigid, concrete or clays, new construction or renovation
Post Reply
k13wjd
Posts: 101
Joined: Sun Jun 10, 2012 8:08 pm
Location: sunny scotland

Post: # 91652Post k13wjd

Bit of a strange one here.

Tommorrow i'm going to be laying 16m2 of marshalls driveline 50 vintage - charcoal.

Bought these a month ago from a local builders supply place ( think locks...)

They were on offer as the pack had been broken up. What i ended up buying was a full pallet never opened, and 2/3rds pallet that had been opened. £8/m2 hence why i bought them.

Looking at the pack that has been open - the are stained quite badly - and a quick test shows a scrub with fairy only removes the residual dust.

Pressure wash once they are down, or will test one with acid ?


Will follow with photo.


Going down on a known solid base, on mortar.

k13wjd
Posts: 101
Joined: Sun Jun 10, 2012 8:08 pm
Location: sunny scotland

Post: # 91653Post k13wjd


RAPressureWashing
Posts: 985
Joined: Wed Aug 15, 2007 3:02 pm
Location: Staines Surrey
Contact:

Post: # 91659Post RAPressureWashing

Had look at the photo, look's sort of oil stain, without knowing what caused the stain, difficult to say what to use, dose it look like it is a surface stain or soaked into the brick?
Roger Oakley BDA(Europe)Member 2006
R&A Pressure Washing Services Ltd
info@rapressurewashing.co.uk
www.rapressurewashing.co.uk

k13wjd
Posts: 101
Joined: Sun Jun 10, 2012 8:08 pm
Location: sunny scotland

Post: # 91660Post k13wjd

Thanks for your reply - as ever the gent !

That brick came from the centre of a pallet - and has never been exposed since being struck......
Tbh the whole pallet is dirty - i just presume this was residual dust from rubbing during transport etc.

I guess they ARE vintage, so were always going to look odd.

I'll pull the rest of the pack apart and see how bad it is. I guess a pressure wash will help once they are down.....



I'll leave my black limestone question for another day/week/month :blush:

k13wjd
Posts: 101
Joined: Sun Jun 10, 2012 8:08 pm
Location: sunny scotland

Post: # 91661Post k13wjd

Image
Image
Image
Image
Image

That one is a from a FULL fresh pallet.......

Image
Image
Image
Image

RAPressureWashing
Posts: 985
Joined: Wed Aug 15, 2007 3:02 pm
Location: Staines Surrey
Contact:

Post: # 91662Post RAPressureWashing

You have more then one type of stain there, look's like a bit of rust? how that would have got into a new pack? maybe metal fillings? some look like it is where the bricks have rubbed together in transit, then there is the brown stains almost like a mould. I'b be inclined to give a few a bleach wash, to see what comes off, the rust won't that's a different approach. If you are going to wait till you have completed the job, allow 4 to 6 weeks if you are concreting them in place before you start hitting the pavers with a pressure washer, allowing time to cure.
Roger Oakley BDA(Europe)Member 2006
R&A Pressure Washing Services Ltd
info@rapressurewashing.co.uk
www.rapressurewashing.co.uk

k13wjd
Posts: 101
Joined: Sun Jun 10, 2012 8:08 pm
Location: sunny scotland

Post: # 91664Post k13wjd

to be honest, im very very reluctant to lay these tomorrow. If I xant clean them up, its a massive headache.

ill speak to Marshalls in the morning. time is ultra tight.....I can see this being abandoned in favour of fake grass/ 2t of chips ....

k13wjd
Posts: 101
Joined: Sun Jun 10, 2012 8:08 pm
Location: sunny scotland

Post: # 91668Post k13wjd

All sorted thanks to Marshalls.

Quality customer service !

Post Reply