My new drive - Good or not good?

Setts and cobbles, tarmac, asphalt, resin systems, concrete whether it's plain, patterned or stencilled, gravels, etc.
Post Reply
Ted
Posts: 585
Joined: Tue Aug 29, 2006 9:02 pm
Location: Luanda, Angola

Post: # 42603Post Ted

I have been away for a while, as my internet connection has been so bad that it is too painful to visit the Brew Cabin. But I now have an improved, although still crap connection, so should visit more often.

Since I moved to Africa I have seen some absolutely appalling construction – so bad you would not believe! The photos below really are not that bad. This is my house which I have rented for a year. The landlord had to install a concrete drive as part of the rental agreement. The photos show his team of workers putting my new drive in…


Below we have a photo of the concrete being placed. Look at that manhole at the top of the picture protruding above the level of the concrete. I have been assured that it is not a problem as they will cut it level with a grinder and patch it up with some render.

Image


Below, by this stage, more concrete has been placed. Look at the thickness of the concrete – is it 2.5cm thick or 3cm thick? Between the concrete block and the placed concrete you can see a small piece of 12.0mm rebar lying on the ground to give you a sense of scale.

Image


In this photo below, you can see the boys working backwards. They decided to make the flower bed bigger to save on concrete but are placing the concrete prior to putting the edgings in!

Image


In the final photo below, you can see the main part of the drive finished. In the bottom left hand corner you can see where today’s concrete neatly merges with yesterday’s pour! The finish is also spectacular!

Image


I am looking forward to seeing how this drive reacts to my 2.5 tonne car when I park it here!

I will post up some photos of this as well as some of the more amusing construction techniques I have witnessed over here shortly.

DNgroundworks
Posts: 1951
Joined: Sat Dec 06, 2008 10:28 pm
Location: Preston, Lancashire

Post: # 42604Post DNgroundworks

proper job :p

Dave_L
Site Admin
Posts: 4732
Joined: Fri Jul 28, 2006 8:47 pm
Location: Somerset
Contact:

Post: # 42609Post Dave_L

Good to hear from you Ted! :)
RW Gale Ltd - Civils & Surfacing Contractors based in Somerset

See what we get up to Our Facebook page

lutonlagerlout
Site Admin
Posts: 15184
Joined: Fri Aug 04, 2006 12:20 am
Location: bedfordshire

Post: # 42618Post lutonlagerlout

welcome back ted :)
I expect those guys are doing their best considering local practises
LLL
"what,you want paying today??"

YOUR TEXT GOES HERE

Suggers
Posts: 934
Joined: Tue Nov 01, 2005 10:57 pm
Location: Buckinghamshire
Contact:

Post: # 42620Post Suggers

Good to see you back in here Ted - entertaining & different as usual....
"Meet the new boss - same as the old boss - We all get fooled again"

Ted
Posts: 585
Joined: Tue Aug 29, 2006 9:02 pm
Location: Luanda, Angola

Post: # 42621Post Ted

By local standards, they have done a good job.

Actually a very good job.

I will post a photo shortly of standard practice for a driveway in this area.

Tony McC
Site Admin
Posts: 8346
Joined: Mon Jul 05, 2004 7:27 pm
Location: Warrington, People's Republic of South Lancashire
Contact:

Post: # 42859Post Tony McC

If you think that's bad, you should see the pavements in Buenos Bloody Aires! Once I've finished sorting out the photies, I'll post a selection to my blog. Trust me: 100mm lips are not uncommon, nor are 300mm deep holes left open to all and sundry.
Site Agent - Pavingexpert

Ted
Posts: 585
Joined: Tue Aug 29, 2006 9:02 pm
Location: Luanda, Angola

Post: # 42969Post Ted

Image

Well here is 2.5 tonnes parked on my drive which is now over a week old and so has gained much of its strength.

There is not a crack in sight!

Why/how is this?

The cement was poor quality rejected dust from China, the water was not particularly clean, the sand was dirty, there are no control joints cut in and the drive is no more than an inch thick in many places.

One could save a lot of money if one could get away with this...

rimexboy
Posts: 916
Joined: Thu Aug 07, 2008 8:31 pm

Post: # 42971Post rimexboy

nice job and a fab car ted :D

Post Reply