Clay pipe adapter

daza1001 · Post: # 113594Post **daza1001** Wed May 31, 2017 6:07 pm

Hello all,

I am trying to connect some 110mm plastic under ground pipe to the existing clay pipe for a toilet connection.
We have done quite a lot of drainage before on jobs but this one is a problem. Normally we make the connection with a flexible rubber adapter. This time though most of the pipe is surrounded in concrete.
Is there any type of internal fitting that can be used ie from a socket on the plastic pipe to the internal of the clay pipe as we have managed to remove a section of existing clay pipe from it socket?
Hope this makes sense

dig dug dan · Post: # 113595Post **dig dug dan** Wed May 31, 2017 6:34 pm

Last time I came across this, I chiseled the concrete off using an sds, revealed about 6inch of pipe then used the rubber adaptor. not sure if you can insert a plastic pipe inside a clay joiner piece?

Post: # 113596Post **seanandruby** Wed May 31, 2017 6:43 pm

Yes you can get an adaptor that pushes inside the clay pipe . Osma do one but can't remember part number. I should think you could pick one up at
Builders merchant. It has a rubber spigot that seals the inside of the pipe and a push in collar as normal. Bit like the one that goes into back of toilet.

daza1001 · Post: # 113597Post **daza1001** Wed May 31, 2017 6:50 pm

Tried today to use a McAlpine one. Phoned McAlpine tech help & they said not to use underground as the rubber will perish? (not sure how) It was a black fitting not brown.

daza1001 · Post: # 113598Post **daza1001** Wed May 31, 2017 6:51 pm

dig dug dan wrote:Last time I came across this, I chiseled the concrete off using an sds, revealed about 6inch of pipe then used the rubber adaptor. not sure if you can insert a plastic pipe inside a clay joiner piece?

Tried but concrete is that strong it kept fracturing the clay pipe

joydivision · Post: # 113599Post **joydivision** Wed May 31, 2017 9:27 pm

4 inch grinder, small coal chisel and persistence.
Come across this loads on 60s/70s houses.
Comes of ok when its a weak lean mix, can be horrendous when its as you describe. Can take hours just to get a connection.
Don't go near it with any sort of breaker.
Good luck
JD

daza1001 · Post: # 113601Post **daza1001** Wed May 31, 2017 9:38 pm

Thanks all

Post: # 113605Post **seanandruby** Thu Jun 01, 2017 1:23 pm

Seal the collar with denso tape to help stop ingress of contaminents to the gasket.

Sat Jun 03, 2017 12:04 am

been here many times
when its really a PITA have used a multiquick fitting
good luck
LLL

Post: # 113624Post **seanandruby** Sat Jun 03, 2017 6:29 am

I have used the Mc Alpine DC1BL before now. This one is recommended by J Atkinson for low level drainage. Breaking around the pipe can be done if you go careful, may take some time but the old clay are so brittle. They aren't very long, about 2 ft so you could break back to the collar, take out the yarn and re-make the joint.

Sat Jun 03, 2017 9:21 am

Great advice Sean, the other option is to get the pipe patch lined so you butt your new pipe up and Davy Brown or one of his people patch lines it,
I still have nightmare about a job in hemel where we ended up going 3 metres back to the IC ,the concrete was as strong and solid as it could be and the pipe just kept breaking

LLL

daza1001 · Post: # 113638Post **daza1001** Sat Jun 03, 2017 5:48 pm

Thanks again all.
Sorted it now.
Used angle grinder & mini chisels we was on last possible section before we then would have to break into main shared 6" main.
Cheers for advice lads.

daza1001 · Post: # 113639Post **daza1001** Sat Jun 03, 2017 5:50 pm

seanandruby wrote:I have used the Mc Alpine DC1BL before now. This one is recommended by J Atkinson for low level drainage. Breaking around the pipe can be done if you go careful, may take some time but the old clay are so brittle. They aren't very long, about 2 ft so you could break back to the collar, take out the yarn and re-make the joint.

That is the fitting we tried. Building Inspector would not allow as he said it is not what the fitting is designed for & the internal diameter reduces to around 80mm.

dig dug dan · Post: # 113643Post **dig dug dan** Sat Jun 03, 2017 7:58 pm

lutonlagerlout wrote:Great advice Sean, the other option is to get the pipe patch lined so you butt your new pipe up and Davy Brown or one of his people patch lines it,
I still have nightmare about a job in hemel where we ended up going 3 metres back to the IC ,the concrete was as strong and solid as it could be and the pipe just kept breaking
LLL

Was that cowper road, where I turned up an met flowjoe? ( whatever happened to him?)

Sat Jun 03, 2017 10:00 pm

Well done, we have some hairy moments on the drainage game :;):

Coincidence, I was on flowjoes site today draindomain.com. he was a good craic on brew cabin, hope he's doing ok.